EV2 stock interchangeablility ? ? ? ? ? ? ? ? ? ? ? ? ??????????????

Discussion in 'General Airgun Chat' started by AirArmsDavid, Dec 13, 2009.

  1. AirArmsDavid

    AirArmsDavid Member

    Joined:
    Apr 20, 2009
    Messages:
    154
    Location:
    Near Lutterworth, Leics
    Club:
    Kibworth
    :)

    Are all EV2 stocks interchangeable between Mk1, 2, & 3 ????

    Thanks for any help!

    David

    :)
     
  2. Ste Hughes

    Ste Hughes Daystate's whipping boy

    Joined:
    Apr 16, 2009
    Messages:
    424
    Location:
    southport
    Club:
    Tawd Vale FT & ARC
    yes :)

    there all the same stock (except the mk3 - but its the same action as the mk2)
     
  3. Willbe

    Willbe I Like BIG Hats!

    Joined:
    Dec 1, 2008
    Messages:
    796
    Location:
    Cheadle, Staffs
    Club:
    Far Coley FTC
    Also as an added note it is possible to fit RN10/Pro Target actions into EV2 stocks. However to use the fitted hamster internally threaded posts need to be made so the factory hamster can still be used.
     
  4. AirArmsDavid

    AirArmsDavid Member

    Joined:
    Apr 20, 2009
    Messages:
    154
    Location:
    Near Lutterworth, Leics
    Club:
    Kibworth
    Thanks guys.

    Do you think there would be much demand for EV2 custom stocks if GINB were to start making them?
    As usual any design from their wide range.

    Seeing as the standard EV2 stock has so much adjustability I'd say not, but they've done a load of Steyr stocks and have orders from Mk4 Grand Prix owners too. I'm just about to send a Mk4 stock over to them for the mould to be made.

    Euro exchange rate doesn't help of course!

    :)
     
  5. rich

    rich Active Member

    Joined:
    Nov 8, 2008
    Messages:
    1,679
    Location:
    Shebbear, N Devon
    If you make a left hand one I'll be pleased to test it for you and give you a report. :):):)
     
  6. Willbe

    Willbe I Like BIG Hats!

    Joined:
    Dec 1, 2008
    Messages:
    796
    Location:
    Cheadle, Staffs
    Club:
    Far Coley FTC
    Would be suprised if GINB dont already offer EV2 inletting for their stocks (as the stocks themselves arn't model specific, but the inletting is) however a lot of EV2s, certainly on the midland FT circuit are wearing custom stocks of various types.
     
  7. chrispro97

    chrispro97 New Member

    Joined:
    Jun 10, 2009
    Messages:
    1,062
    Location:
    atherstone
    Club:
    purley chase ftc
    paul wilson does them mine was inleted for protarget and it had to be inleted for the pressure gauge on ev2 by a lad down the greyhound matey
     
  8. AirArmsDavid

    AirArmsDavid Member

    Joined:
    Apr 20, 2009
    Messages:
    154
    Location:
    Near Lutterworth, Leics
    Club:
    Kibworth
    No, GINB don't have a mould for the EV2 inletting, hence the question.

    :)
     
  9. rich

    rich Active Member

    Joined:
    Nov 8, 2008
    Messages:
    1,679
    Location:
    Shebbear, N Devon
    It's very similar to the pro-target. The differences are the hole for the pressure gauge and the recess adjacent, and the holes underneath where the hamster pins pass through, maybe also the locking screw as well. All the main dimensions look the same.

    I'm still prepared to try a left hander out for you. Action waiting...... :D
     

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice